Charge controllers
No product matches these criteria.
Our selection
Victron Energy BlueSolar MPPT 75/15
$70.55 (4)
A compact, well-priced MPPT charge controller from a name the off-grid world trusts: the ideal choice for a small van, boat, or cabin solar setup.
- Charge current: 15A
- PV input: Max 75V
- Type: MPPT
- Battery voltage: 12/24V (auto)
- MPPT, up to 30% more yield than PWM
The BlueSolar 75/15 from Victron Energy is an MPPT (Maximum Power Point Tracker) solar charge controller. Placed between the panels and the battery, it constantly locates the panels' maximum power point, improving energy harvest, especially under cloudy skies, by up to 30% over a PWM controller. Its BatteryLife function manages charging intelligently to extend battery life, and it auto-detects 12V or 24V systems. A dependable, compact choice for a small off-grid solar installation.
In-depth reviewRead our full review →
4.0/5
The BlueSolar 75/15 is the kind of part US van-builders and boat owners tend to buy once and never think about again. One reviewer running a 220W/440W 12V/24V panel setup called it efficient and versatile, praising how well the MPPT algorithm tracks maximum power, and noted the VE.Direct Bluetooth dongle actually extends monitoring range better than Victron's built-in Bluetooth units, useful if the controller ends up several meters from where you check it. A first-timer who added a 170W panel to a jeep's rooftop tent found the whole project surprisingly approachable thanks to this controller, with one real gripe: the connectors are tight for 10AWG wire, 12AWG fits cleanly, so plan your wire gauge accordingly if voltage drop matters over a longer run. The included documentation draws some complaints, small print and instructions that assume prior electrical knowledge, so budget extra time your first setup. Once wired in, though, owners consistently describe it as reliable and precise, exactly what you want from a component you are bolting inside a wall and forgetting about.
Thlevel 30A PWM
See price and availability (35)
The Thlevel 30A PWM keeps it simple: charge control for a 12V/24V lead-acid battery, an LCD screen, and dual 5V USB, all at a budget-friendly price.
- Type: PWM, 30A
- Voltage: 12V/24V automatic
- Compatibility: Lead-acid (flooded, AGM, GEL)
- USB output: 5V/1.2A
- Simple, reliable 30A PWM, LCD screen, dual USB
The Thlevel 30A PWM is a solar charge controller for 12V or 24V systems with automatic voltage detection, built for lead-acid batteries (flooded, AGM, GEL). It handles up to 30A of charging current and 10A of load current, with a maximum solar input of 50V and a 5V/1.2A USB output to charge a device directly. Its LCD screen shows voltage and charge status, backed by full protections against short circuit, overload, and reverse polarity. A simple, budget-friendly option for a small standalone solar system.
In-depth reviewRead our full review →
3.5/5
We tested the Thlevel 30A PWM on a modest setup: a 100W panel and a 12V AGM battery in a garden shed. Setup is quick, the automatic 12V/24V detection works with no fiddling, and the LCD screen clearly shows battery voltage and charge status. The USB port comes in handy for topping off a phone without pulling straight from the battery. Float charge and low-voltage cutoff settings are easy to adjust with the three buttons once you have skimmed the manual. The lack of MPPT tracking is the main gap, it would squeeze a few extra watts out of low light, and strict lead-acid compatibility rules out lithium batteries outright. But for a simple job, a shed, a small cabin, or a modest backup system, it does exactly what is asked of it, no surprises, and its low price makes it a safe way to get started with standalone solar. Note: at the time of writing, this exact listing shows as temporarily out of stock on Amazon; check current availability before ordering.
Victron Energy SmartSolar MPPT 100/20
See price and availability (33)
The benchmark solar charge controller: 100V, 20A, built-in Bluetooth, and up to 98% efficiency. The Victron SmartSolar MPPT 100/20 gets more from your panels.
- Max PV voltage: 100V (12/24/48V auto)
- Charge current: 20A
- Efficiency: Up to 98% (MPPT)
- Monitoring: Built-in Bluetooth (VictronConnect)
- 98% MPPT with Bluetooth and Victron reliability
The Victron SmartSolar MPPT 100/20 is a premium solar charge controller, known across the off-grid world for its reliability and efficiency. It accepts up to 100V of solar input and delivers 20A of charge current, on 12V, 24V, or 48V systems with automatic detection. Its MPPT technology harvests up to 30% more energy than a conventional PWM controller, with efficiency up to 98%. Built-in Bluetooth lets you track output in real time and adjust settings from the VictronConnect app.
In-depth reviewRead our full review →
4.1/5
The Victron SmartSolar MPPT 100/20 is the controller you install when you never want to think about it again. Victron is a benchmark name in the off-grid world, and this model shows why: in a van or RV build, it genuinely squeezes more out of the panels thanks to real MPPT tracking, a difference you can feel over a plain PWM controller under a hazy sky. The built-in Bluetooth is a real everyday plus, the VictronConnect app shows live output, a 30-day history, and lets you tune charge settings with no extra cables. Build quality feels like it is meant to last for years. Its downsides are a price above budget Chinese controllers and Amazon's habit of hiding the checkout price until it hits your cart, worth a quick price check before you commit. It also has no physical screen, so reading anything without a phone nearby means relying on status LEDs alone. But for a reliable, durable installation, Victron remains the safe bet, and this is one of its most popular sizes.
Renogy Rover 20A
See price and availability (20)
20A of charge, 100V input and up to 99% tracking efficiency, with an LCD screen: the Renogy Rover 20A handles small 12/24V solar setups.
- Max PV voltage: 100V (12/24V auto)
- Charge current: 20A
- Tracking efficiency: Up to 99% (MPPT)
- Screen: LCD, Bluetooth optional
- 20A and LCD screen for a compact 12/24V setup
The Renogy Rover 20A is a compact MPPT solar charge controller, designed for medium-sized 12V and 24V setups. It accepts up to 100V solar input and delivers 20A of charge, meaning up to 260W of panels at 12V and 520W at 24V. Its MPPT technology reaches up to 99% tracking efficiency, and its LCD screen shows output and battery status in real time. Compatible with all technologies (lead-acid, gel, AGM, lithium LiFePO4), it accepts an optional Bluetooth module for remote monitoring.
In-depth reviewRead our full review →
3.9/5
The Renogy Rover 20A is the controller you fit on a small setup without breaking the bank: two 100W panels on a van, a garden shed, a site cabin. For this kind of use, it does exactly what is asked of it. The LCD screen is a real plus compared with display-less controllers: you see battery voltage and charge current straight away, without reaching for your phone. Automatic 12V/24V detection works well, and the included temperature sensor avoids surprises in hot weather. A few honest caveats: the screen is not backlit, which makes it hard to read at night or from an awkward angle, the IP32 rating means a sheltered spot rather than full outdoor exposure, and for real remote monitoring you need to add the BT-1 Bluetooth module, sold separately. Nothing dealbreaking though: for a reliable, affordable small solar setup, the Rover 20A remains a sound choice.
Renogy Rover 60A
See price and availability (12)
60A of charge, 150V input and automatic 12/24/36/48V detection: the Renogy Rover 60A MPPT handles the most demanding solar setups.
- Max PV voltage: 150V (12/24/36/48V auto)
- Charge current: 60A
- Tracking efficiency: Up to 99% (MPPT)
- Screen: LCD, Bluetooth optional
- 60A, 150V and 12-48V auto for large setups
The Renogy Rover 60A is a premium MPPT solar charge controller, designed for 12V, 24V, 36V and 48V setups. It accepts up to 150V solar input and delivers 60A of charge, meaning up to 3200W of panels at 48V. Its MPPT technology reaches up to 99% tracking efficiency, and its LCD screen shows output and battery status in real time. Compatible with all technologies (lead-acid, gel, AGM, lithium LiFePO4), it accepts an optional Bluetooth BT-1/BT-2 module for remote monitoring.
In-depth reviewRead our full review →
4.1/5
The Renogy Rover 60A is built for solar setups that have outgrown a small controller. Tested on a 24V system with close to 1000W of panels, it never seemed to struggle: the 60A charge current leaves real headroom, and the auto-detection up to 48V is handy if the setup ever moves to a higher voltage. The LCD screen is clear and readable in full sun, showing voltage, current and charge status directly without needing a phone. Switching to lithium was painless thanks to the configurable user mode. The only real drawbacks: Bluetooth stays optional (you need to add a BT-1 module for remote monitoring), and there is no fan, everything relies on the aluminum heatsink, which is plenty in normal use but runs a bit warm at peak output in summer. For a large setup that has outgrown a 40A controller, this is a solid choice, and a far more complete one than the Rover Lite.
Renogy Rover 40A
See price and availability (8)
40A of charge, 100V input and up to 99% tracking efficiency, with an LCD screen: the Renogy Rover 40A handles the most generous 12/24V solar setups.
- Max PV voltage: 100V (12/24V auto)
- Charge current: 40A
- Tracking efficiency: Up to 99% (MPPT)
- Screen: LCD, Bluetooth optional
- 40A and LCD screen for large 12/24V setups
The Renogy Rover 40A is a premium MPPT solar charge controller, designed for 12V and 24V setups. It accepts up to 100V solar input and delivers 40A of charge, meaning up to 520W of panels at 12V and 1040W at 24V. Its MPPT technology reaches up to 99% tracking efficiency, and its LCD screen shows output and battery status in real time. Compatible with all technologies (lead-acid, gel, AGM, lithium LiFePO4), it accepts an optional Bluetooth module for remote monitoring.
In-depth reviewRead our full review →
4.0/5
The Renogy Rover 40A is the controller you choose when your solar setup starts getting serious. Its 40A charge current lets it handle large panel arrays, up to 520W at 12V and double at 24V, where a 20A controller would quickly saturate. Its MPPT technology really gets the most from the panels, with tracking efficiency that climbs very high. We really like the built-in LCD screen, which shows output, voltage and charge status directly without needing a phone, while still allowing you to add a Bluetooth module for remote monitoring. It handles all battery types, including lithium, via configurable profiles. The only things to plan for are the price, above a small controller, and the Bluetooth not being built in as standard, unlike some rivals. But for a robust, reliable 12/24V setup, it is an excellent controller.
LNEX CTM12-10
See price and availability (7)
A waterproof, ultra-thin 10A PWM solar charge controller: the LNEX CTM12-10 protects your battery even when exposed to rain and sea spray.
- Type: PWM, 10A
- Waterproofing: IP65, ultra-thin 0.9 in (22 mm) housing
- Voltage: 12/24V automatic
- Compatibility: LiFePO4, AGM, Gel, lead-acid
- PWM 10A, IP65 waterproof, LCD screen, temp sensor
The LNEX CTM12-10 is a 10A PWM solar charge controller designed for small 12V or 24V setups with automatic voltage detection. Its IP65 waterproof housing and ultra-thin 0.9 in (22 mm) profile make it a great fit for a camper van, a boat, an off-grid cabin or any outdoor use exposed to the weather. It supports LiFePO4, AGM, Gel, flooded, calcium and EFB batteries, with 5-stage charging, a backlit LCD screen and an included temperature sensor for accurate compensation.
In-depth reviewRead our full review →
3.6/5
On a small camper van solar kit, this LNEX lives up to its waterproofing claim: left outside in the rain for several weeks, it kept working without a single hiccup. The backlit LCD screen stays sharp and readable even in bright sunlight, and the included temperature sensor is reassuring for charging accuracy, especially in winter. The ultra-thin housing slots easily into a tight wall cavity where a standard controller simply would not fit. Two honest downsides to know before buying: the screen only shows amps, never watts, so you have to work out real power yourself, and there is no front flap for wiring, meaning you have to pre-wire the unit before screwing it into place. For a small 12/24V setup planned properly from the start, whether with a lead-acid or lithium battery, the ruggedness-to-price ratio remains convincing.
Zendure Hub 2000
$675.65 $540.25
(2)
The smart PV hub that adds storage to an existing balcony setup: 2 MPPT (1800 W), AB batteries up to 7.68 kWh and fine control, at a lower cost.
- Solar input: 1800 W, 2 MPPT controllers
- Storage: AB batteries expandable to 7.68 kWh
- Function: Storage hub to pair with a microinverter
- Protection: IP65, app monitoring
- Adds storage to a balcony array on a budget
The Zendure SolarFlow Hub 2000 is a smart PV hub that brings storage to an existing balcony system. With two MPPT controllers (1800 W of solar input), it drives the charging and discharging of Zendure AB batteries up to 7.68 kWh, and pairs with a microinverter to feed energy into the home. An IP65 enclosure, app monitoring and Shelly compatibility make it an affordable way to optimize self-consumption without starting from scratch.
In-depth reviewRead our full review →
3.9/5
The Hub 2000 is the piece that early balcony kits were missing: rather than replacing everything, it grafts an energy reserve onto an existing setup. Its role is clear: manage solar input through its two MPPT trackers (up to 1800 W), charge the Zendure AB batteries during the day, then discharge them in the evening through a microinverter. In our tests, the app integration is polished, with real-time monitoring of production and charge, and Shelly compatibility appeals to home-automation fans. It is also the most affordable way in the range to try storage. Two limits to understand before buying: unlike the Hyper 2000, the Hub 2000 has no built-in inverter, so you need to add a compatible microinverter; and it handles only two MPPT inputs, where the Hyper offers four. But to turn a simple balcony kit into a system with storage, without a big investment, the Hub 2000 remains a smart gateway into the SolarFlow ecosystem.
Steca Tarom 4545
$233.19 (2)
45A of charge, a graphic LCD screen and a 12-year data logger: the Steca Tarom 4545 reliably drives good-sized 12/24V solar setups.
- Type: Hybrid PWM, 45A
- System voltage: 12V (24V) automatic
- Screen: Backlit graphic LCD
- Data logger: 12 years of history
- 45A, LCD screen and 2 programmable contacts
The Steca Tarom 4545 is a premium PWM solar charge controller, made in Germany for good-sized 12V and 24V setups. It accepts up to 45A of charge current, handling roughly 700W of panels at 12V and 1400W at 24V. Its backlit graphic LCD screen shows output, charge status and history in real time, while its data logger keeps up to 12 years of records. Two programmable multi-function contacts can drive lighting, a generator or a surplus load.
In-depth reviewRead our full review →
3.2/5
Fitted to an off-grid cabin system with a decent panel array, the Steca Tarom 4545 commands respect straight out of the box: a sturdy enclosure, an oversized terminal block that takes 35 mm2 cable without fuss, and a graphic screen showing output, charge status and recent history at a glance. The menu takes a bit of patience the first time round (plenty of options, multi-function contacts, timers), but once set up it just runs. The twelve-year data logger is a real plus for anyone tracking output over the long haul. Two things to know before buying: it is a PWM controller, not MPPT, despite the premium price tag, and the IP31 rating calls for a sheltered enclosure. One Amazon review also flagged a state-of-charge glitch, an isolated case in our research. For a solid, well-monitored 12/24V setup, the Tarom 4545 remains a safe bet.
Steca Solsum 0606
$19.81 (2)
Light, reliable and affordable: the Steca Solsum 0606 regulates solar charging on small 12V/24V lead-acid setups, drawing under 4 mA of self-consumption.
- Type: PWM, 6A
- Voltage: 12V/24V automatic
- Battery: AGM/gel (factory setting)
- Consumption: Under 4 mA
- Simple, reliable, very low self-consumption
The Steca Solsum 0606 is an entry-level PWM solar charge controller for small off-grid 12V or 24V setups (automatic detection). It delivers up to 6A of charge current, handling roughly 72W of panels at 12V and 144W at 24V. Factory-set for AGM and gel batteries, it shows charge status through 4 multicolor LEDs and carries full protection (overcharge, deep discharge, reverse polarity, short circuit). A simple, rugged controller, among the most widely used in off-grid solar kits.
In-depth reviewRead our full review →
3.4/5
The Steca Solsum 0606 runs a small backup system in a garden shed, with a 50W panel and a 12V AGM battery. Nothing to set up on install: 12V/24V detection happens on its own, and the colored LEDs give an instant read on charge status, no screen to interpret. Its claimed self-consumption under 4 mA is a real plus for a setup left switched on permanently off a small battery. The compact enclosure, 5.7 x 3.9 x 1.2 in (145 x 100 x 30 mm) and 0.33 lb (150g), fits almost anywhere. The downsides are the total lack of a numeric display (just LEDs) and the compatibility strictly limited to AGM/gel lead-acid batteries out of the box, with no optional accessory to change the profile. For simple use on a tight budget, this small German controller does exactly what is asked of it, no surprises and no faults reported after several months of continuous use.
Epever XTRA1210N
See price and availability (2)
A budget 10A MPPT controller from a brand US off-gridders trust for the long haul: the Epever XTRA1210N optimizes a small kit and protects the battery.
- Type: MPPT, 10A
- Voltage: 12/24V automatic
- PV input: Up to 100V
- Compatibility: Lead-acid, gel, AGM, lithium
- MPPT 10A, up to 30% more yield than PWM
The Epever XTRA1210N is a 10A MPPT solar charge controller for small 12V or 24V systems, with automatic voltage detection. MPPT technology extracts more energy from panels than a basic PWM controller, a gain of up to 30% in low light. It accepts a PV input voltage up to 100V, handles lead-acid, gel, AGM and lithium batteries, and protects against overcharge, deep discharge, short circuit and reverse polarity. An optional XDS2 remote display shows output and state of charge at a glance.
The XTRA1210N tends to show up in small, unglamorous jobs, a shed light circuit, a backup system nobody thinks about until the power goes out, and it earns loyalty exactly there. One owner installed it to keep a small standby power system topped off and reported it still running strong more than five years later, having survived a close lightning strike on a neighboring property without issue, enough that they came back to buy a second Epever unit for the shed. Another new buyer summed up the experience simply: it works well, though the manual could be clearer, plan on reading it carefully rather than guessing at the button sequence for your battery type. Reviews are thin in number but consistently positive, and the brand's reputation in the wider US off-grid community, built mostly on its larger Tracer-series controllers, extends to this smaller 10A unit. For a small van, shed, or backup solar system where 10A of charge current is enough, 130W at 12V or 260W at 24V, it is a dependable, low-cost way to add real MPPT tracking instead of a basic PWM controller.
Steca PR 2020 IP65
$182.44 (1)
An IP65 enclosure built for salt, humidity and dust: the Steca PR 2020 IP65 regulates 20A of solar charge where a standard controller would not survive.
- Type: PWM, 20A
- Rating: IP65 weatherproof
- Screen: LCD, AtonIC algorithm (SOC)
- Certified: Tropical use (DIN IEC 68-2-30)
- IP65 enclosure for salty and humid environments
The Steca PR 2020 IP65 is a 20A PWM solar charge controller, specifically built to work in demanding environments: high salinity, humidity and dust. Its weatherproof IP65 enclosure suits marine, agricultural or building-site installations exposed to the elements. It auto-detects a 12V or 24V system and handles roughly 240W of panels at 12V and 480W at 24V. Its LCD screen shows charge status as a percentage thanks to the self-adaptive Steca AtonIC algorithm, for optimal battery care.
In-depth reviewRead our full review →
3.5/5
The Steca PR 2020 IP65 joined a sailboat's solar setup, where humidity and sea spray finish off most standard controllers within a couple of seasons. Its clear weatherproof enclosure lets you see the electronics inside and screws firmly to the bulkhead, with three cable glands for the module, battery and load leads. The LCD screen clearly shows the charge percentage thanks to the AtonIC algorithm, with no technical jargon to decode. The tropical-use certification is reassuring for long-term humid-climate durability. The downsides: no Bluetooth or app, the screen stays basic compared with recent MPPT controllers, and the price runs well above a non-weatherproof PR 2020 for the same 20A rating. But for marine, agricultural or outdoor building-site use, that IP65 rating clearly justifies the price gap over a standard controller that would eventually give up the ghost.
Victron Energy SmartSolar MPPT 150/35
See price and availability (15)
The only controller in our range rated for 150V PV: wire your panels in series. MPPT 35A, built-in Bluetooth, up to 98% efficiency.
- Max PV voltage: 150V (12/24/36/48V auto)
- Charge current: 35A
- Efficiency: Up to 98% (MPPT)
- Monitoring: Built-in Bluetooth (VictronConnect)
- 150V for series-wired panels, Bluetooth, Victron reliability
The Victron SmartSolar MPPT 150/35 is a premium solar charge controller rated for up to 150V solar input, letting you wire several panels in series rather than in parallel and cut losses over long cable runs. It delivers 35A of charge on 12V, 24V, 36V, or 48V systems, with MPPT efficiency up to 98%. Built-in Bluetooth and the VictronConnect app let you track output in real time and adjust every setting with no extra hardware.
In-depth reviewRead our full review →
4.2/5
You install the SmartSolar 150/35 once a plain 75V or 100V controller becomes too tight for the build. On a van with two 200W panels wired in series rather than parallel, the gain is immediate: less loss in the wiring, a thinner cable gauge does the job, and the controller keeps tracking the maximum power point without a hitch, even under a hazy sky. Built-in Bluetooth is a genuine everyday plus, the VictronConnect app shows live output, a 30-day history, and lets you tweak charge thresholds with no cover to open. Victron's build quality inspires confidence, and the case doesn't run hot even under full load. The real downsides: the price sits well above a plain PWM controller or a budget Chinese MPPT, the IP43 rating means it needs shelter from direct spray, and Amazon hides the checkout price until it's in your cart, worth a quick check before you commit. But for a build that goes beyond 100V PV, this is one of the safest picks on the market today.
